★ Independent welder reviews, process guides and shop-tested builds
Welding Codes & Standards

Weld All Around Symbol: Meaning and Examples

By Rafael Salazar Nov 8, 2026 ⏱ 3 min read
Welder welding all the way around a steel post on a base plate

The weld-all-around symbol is a small open circle drawn at the junction where the arrow meets the reference line of a welding symbol. It means the weld continues completely around the joint, following the full outline of the part, such as around a pipe, tube, post or base plate. Read the weld type, size and side from the reference line as usual; the circle just tells you not to stop. It can be combined with the field weld flag to mean “weld all around, in the field.”

Weld-all-around callouts are everywhere on fabrication drawings: posts on base plates, tubes through plates, brackets and gussets. Missing that little circle is one of the most common reasons parts come back for rework.

Diagram of the weld all around symbol showing a fillet weld with a circle at the junction and a ring-shaped weld
The circle means the weld goes all the way around the joint.

How to Read the Weld-All-Around Symbol

  1. Find the circle at the arrow-reference line junction. If it’s there, the weld goes all around the joint.
  2. Read the weld symbol: a triangle is a fillet weld; V, bevel and other shapes are groove welds.
  3. Check the side: below the reference line is the arrow side; above is the other side.
  4. Read the size to the left of the weld symbol.
  5. Check for a flag: a flag at the same junction means it’s also a field weld.
  6. Read the tail for process or notes.

Note that a weld-all-around circle normally has no length number, because the weld runs the entire perimeter.

Weld All Around Examples

Weld all around symbol examples: field weld all around, groove all around, fillet with process, both sides all around
Four common weld-all-around callouts and what they mean.

Where You’ll See Weld All Around

  • Square or round posts welded to base plates
  • Pipe or tube passing through a plate or flange
  • Brackets, lugs and gussets that need a sealed perimeter
  • Handrail posts, bollards and sign supports
  • Tanks and enclosures where a sealed seam keeps out water

An all-around fillet seals the joint, which helps prevent corrosion between surfaces and is often required for galvanized parts so trapped liquids don’t cause problems. Read welding galvanized steel for related safety tips.

Weld All Around on Multiple Surfaces

The weld-all-around symbol applies to a continuous series of connected joints, even if the joint changes direction or plane, such as around all four sides of a square tube. If the weld must change type or size partway around, the drawing should show separate symbols for those segments instead of the all-around circle.

Common Mistakes With Weld All Around

Comparison of correct practices and common mistakes when welding all around
Avoid these common weld-all-around mistakes.

Tips for Welding All Around

  • Plan your stops and starts. On a round tube, weld in two halves, overlapping slightly at the top and bottom. Grind starts so tie-ins are smooth.
  • Control distortion. Weld opposite sides alternately on posts and plates to keep them square; tack first.
  • Corners on square tube: carry the bead around corners without stopping, or overlap starts on the flats where they’re easy to blend.
  • Reach every side: rotate the part or use a positioner so you’re not forced into awkward angles.
  • Check size all around with a fillet gauge, especially at corners where leg size tends to shrink.

For more on fillets, read fillet weld symbols and tack welding techniques.

Weld All Around in ISO 2553

ISO 2553 uses the same idea: a circle at the junction of the arrow and reference line means a peripheral weld all around. Remember that ISO drawings also use a dashed identification line to show which side is welded. Confirm the standard before reading the arrow and other side. See the welding symbols chart.

Weld All Around Symbol FAQs

What does a circle on a welding symbol mean?

An open circle at the arrow-reference line junction means weld all around: the weld continues around the entire joint.

What does a circle and a flag mean on a weld symbol?

Weld all around, made in the field (on site). See the field weld symbol.

Does weld all around include both sides?

Only if the symbol shows welds on both sides of the reference line. The circle controls continuity around the joint, not which side is welded.

Is a filled circle the same as weld all around?

No. Weld all around is an open circle at the junction. Other circular symbols (such as spot and seam weld symbols) are drawn on the reference line itself.

Do I need a length on a weld-all-around symbol?

No. The weld runs the full perimeter, so a length isn’t needed.

Sources

Leave a Comment

Your email address will not be published. Required fields are marked *