★ Independent welder reviews, process guides and shop-tested builds
Miller Welders

Millermatic 255 vs Multimatic 255: Which Miller Should You Buy?

By Rafael Salazar Nov 15, 2026 ⏱ 4 min read
Two large blue Miller-style welding machines side by side in a fabrication shop

Choose the Millermatic 255 if you only need MIG, pulsed MIG and flux-cored welding. Choose the Multimatic 255 if you also want DC stick and DC TIG, or if you work on different power supplies from 208 to 575 volts. Both use the same 230 amp, 60% duty cycle MIG rating and weigh 84 pounds without running gear.

These two Miller machines look alike but target different shops. We compared Miller’s spec sheets and dealer listings to show what really differs.

We research every product using manufacturer specifications, published manuals and owner feedback. As an Amazon Associate, GenuineWelding earns from qualifying purchases at no extra cost to you. Prices change often, so check the current price before you buy.

Quick Comparison

Spec Millermatic 255 Multimatic 255
Processes MIG, pulsed MIG, flux-cored MIG, pulsed MIG, flux-cored, DC stick, Lift-Arc TIG, pulsed TIG
MIG rated output 230 A at 25.5 V, 60% 230 A at 25.5 V, 60%
Stick rated output Not available 200 A at 28 V, 60%
TIG rated output Not available 275 A at 21 V, 60%
Amperage range 20-350 A 5-350 A
Input power 208-240V (Auto-Line version 208-575V) Auto-Line 208-575V
Open-circuit voltage 87 VDC 81 VDC
Weight (machine only) 84 lb 84 lb
Warranty 3 years (gun 90 days) 3 years (gun 90 days)

The Key Difference: Processes

The Millermatic 255 is a pure wire-feed machine. It runs MIG, pulsed MIG and flux-cored with Auto-Set Elite parameters and USB software updates. The Multimatic 255 does all of that and adds DC stick, including E6010 electrodes, plus DC Lift-Arc TIG and pulsed TIG. If you only ever run a wire gun, the extra processes are a cost you do not need.

Welding bench with MIG gun, TIG torch and stick holder cables laid out beside a machine
Illustration: the Multimatic adds stick and TIG leads to the same MIG platform.

Input Power and Portability

The base Millermatic 255 is specified for 208 to 240 volt single phase, and Miller sells an Auto-Line version for 208 to 575 volts. The Multimatic 255 in the listing we link includes Auto-Line, so it connects to any single-phase supply from 208 to 575 volts without manual linking. Both weigh 84 pounds as a bare machine and 148 pounds with Miller’s EZ-Latch running gear. Miller also notes the Multimatic is more than 50 percent lighter than the older Millermatic 252.

Performance

For MIG, performance is essentially the same on paper: 230 amps at 25.5 volts at a 60 percent duty cycle. Both support pulsed MIG, which Miller says gives lower heat input, less distortion on thin material and less spatter. For aluminum on either machine you need a spool gun or push-pull gun, which Auto-Gun Detect recognizes automatically. For deeper background see our best pulse MIG welder guide.

Who Needs TIG?

The Multimatic 255’s TIG is DC only, so it handles steel, stainless and similar metals but not aluminum TIG, which needs AC. If you need AC TIG, look at our best Miller TIG welder guide. For lower budgets see the best multi-process welders under $1,000.

Millermatic 255 Details

Miller Millermatic 255 MIG Welder – MIG specialist

Miller Millermatic 255 MIG Welder

Miller Millermatic 255 MIG Welder

208/240V MIG and pulsed MIG machine with Auto-Set Elite

Check Price on Amazon

Bottom line: The Millermatic 255 is a dedicated MIG and pulsed MIG machine with a 230 A, 60% duty cycle rating. It is the better pick for shops that only need MIG and flux-cored welding.

Pros

  • Strong 60% duty cycle at 230 A
  • Pulsed MIG for aluminum and thin material
  • Auto-Gun Detect for spool guns and push-pull guns
  • Simpler MIG-only control layout

Cons

  • No stick or TIG
  • Base model needs 208-240V
  • Higher cost than many MIG-only machines

Best for: fab shops, auto and trailer repair, and anyone who only needs MIG and pulse MIG.

Multimatic 255 Details

Miller Multimatic 255 Multiprocess Welder – Multiprocess pick

Miller Multimatic 255 Multiprocess Welder

Miller Multimatic 255 Multiprocess Welder

MIG, pulsed MIG, stick (6010), Lift-Arc TIG and pulsed TIG on 208-575V

Check Price on Amazon

Bottom line: The Multimatic 255 adds DC stick and DC TIG to the same MIG performance, and its Auto-Line power management accepts any single-phase voltage from 208 to 575 V. It suits shops that need one machine to do everything.

Pros

  • Four process families in one machine
  • Auto-Line works on 208-575V single phase
  • Handles E6010 and DC TIG
  • Lighter than older Millermatic 252

Cons

  • Higher cost
  • Needs a TIG torch and gas setup for TIG
  • No AC TIG for aluminum TIG welding

Best for: MRO crews and fabricators who weld on different jobs and power supplies and need TIG and stick as well as MIG.

Which Should You Choose?

Choose the Millermatic 255 if:

  • You only weld with a wire feed gun (MIG, pulsed MIG or flux-cored).
  • You have a fixed 208-240V supply.
  • You want to keep the cost down within the Miller line.

Choose the Multimatic 255 if:

  • You also need stick or TIG without buying a second machine.
  • You move between shops with different single-phase voltages up to 575V.
  • You want one machine to cover repair, fabrication and light production.

FAQs

What is the difference between the Millermatic 255 and Multimatic 255?

The Millermatic 255 is MIG, pulsed MIG and flux-cored only. The Multimatic 255 adds DC stick and DC TIG and uses Auto-Line input power.

Do both machines have the same MIG output?

Yes. Miller rates both at 230 amps at 25.5 volts at 60 percent duty cycle.

Can the Multimatic 255 TIG weld aluminum?

No. Its TIG output is DC, so it suits steel and stainless. Aluminum TIG needs an AC-capable machine.

How heavy are they?

Miller lists 84 pounds for the machine only and 148 pounds with EZ-Latch running gear for both.

Do I need a spool gun for aluminum?

Yes, for aluminum MIG you should use a spool gun or push-pull gun; Auto-Gun Detect adjusts the settings when you swap guns.

Final Verdict

For a shop that welds with a wire feed gun all day, the Millermatic 255 is the focused choice. If you want stick and TIG available as well, or you work across different voltages, the Multimatic 255 is the more versatile investment.

Sources

Leave a Comment

Your email address will not be published. Required fields are marked *